Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Daly City Homeowners
Chimney repair in Daly City usually starts with a small leak or a crumbling crown that goes unnoticed until water shows up inside the firebox. Our technicians have up to 15 years of experience reading exactly those symptoms, and we show you what we find before we recommend anything. We handle chimney sweeping, chimney inspection, and repair as three parts of one job, so you’re not stuck trying to coordinate a sweep with one company and a mason with another. On a clear day a repair that doesn’t need parts on hand can often be scheduled the same day. Call (866) 885-7416 and we’ll talk through what you’re seeing.

Chimney Cap Installation
Chimney Cap Installation is the fitting of a protective cover over the top of your flue that keeps rain, birds, and debris out while letting smoke and gases escape. You need one if your flue is open to the sky, if you’ve had birds or squirrels in the firebox, or if water is getting down the flue during our winter rains. We measure the flue, match a cap to your chimney’s size and draft, and secure it against wind. Typical cost in Daly City runs $180 to $450 depending on flue count, cap material, and whether the cap needs custom fitting. The written estimate sets the final price.
Why an Open Flue Is a Problem
An uncapped flue takes in water every time it rains, and that moisture mixes with creosote and soot to make a corrosive paste against the flue walls. It also gives animals an easy entry into a warm cavity. A cap is a small job with a real payoff.
Matching the Cap to the Flue
A cap that’s too small chokes draft and pushes smoke back into the room. A cap that’s oversized catches wind and rattles. We size it to the flue opening and to how your appliance drafts, then anchor it so it stays put.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is swapping a failed or missing cap for a new one before water and wildlife get into the flue. Your existing cap needs replacing if it’s rusted through, dented from a branch or storm, loose on its mounts, or missing its mesh screen. We remove the old cap, inspect the flue top while it’s exposed, and fit a new cap sized correctly for the opening. Replacement typically runs $190 to $475 in Daly City, depending on the flue count and cap style you choose. We’ll write the price down before work begins, and the written estimate is what you pay.
When Storm Damage Is the Cause
Winter storms and wind here can take a cap off or fold its screen in. If a limb or wind gust has moved your cap, have the flue top checked before next season. A loose cap is a water path waiting to happen.
What the New Cap Includes
Every replacement includes the new cap, correct sizing, and secure mounting, plus a look at the flue tile and crown while we’re up there. If we find a crown problem, you’ll hear about it and see the photo before anything gets added to the job.
Chimney Liner Installation
Chimney Liner Installation is fitting a new flue liner inside the chimney when the original clay tiles are cracked, missing, or improperly sized for the appliance. You need it if an inspection shows gaps in the tile, a flue too large for a modern insert, or a chimney that has never had a liner. We install DuraFlex flexible liner systems for retrofits and non-standard chimneys, and in qualifying chimneys we use the HeatShield liner restoration system, which can repair certain flues without the disruption of a full replacement. Liner installation in Daly City typically runs $2,400 to $5,800 depending on length, flue size, and whether the chimney needs a full reline or can be restored. The written estimate fixes the number.
Repair or Replace: Which Fits This Chimney
Not every cracked flue needs a full liner. If the tile and joints qualify, HeatShield resurfacing can restore the existing liner at lower cost and with less mess. If the flue is unlined, cracked through, or the wrong size, a DuraFlex liner is the sound fix. We tell you which one your chimney calls for and show you the evidence behind that call.
Why the Flue Size Matters
An oversized flue cools smoke too quickly, which builds creosote and weakens draft. An undersized flue can’t move the volume your appliance produces. Getting the diameter right is as important as getting a liner in at all.
Chimney Flashing Repair
Chimney Flashing Repair is fixing the metal seals where your chimney meets the roof, the spot where most chimney leaks actually start. You need it when you see water stains on the ceiling near the chimney, rust streaks on the flashing, loose or lifting metal, or cracked sealant at the roof joint. We reset, seal, or replace the flashing and step flashing, matching it to your roofing material. Flashing repair in Daly City typically runs $350 to $900 depending on access, the roof pitch, and how much of the flashing needs to be rebuilt. The written estimate sets the final price before we start.
A Leak Isn’t Always the Flue
Homeowners often assume a ceiling stain means the flue is failing. Just as often the water is coming in at the flashing and running down the outside of the chimney. We trace the path before recommending anything.
What Leaks Left Alone Do
Water at the flashing works into the framing and the masonry around the chimney over time. Rot and spalling both get more expensive the longer they sit. Fixing flashing early is far cheaper than repairing what it damages underneath.
Chimney Crown Repair
Chimney Crown Repair is fixing the concrete cap that slopes across the top of the chimney to shed water away from the flue. The crown needs repair when it’s cracked, flaking, or pitted, or when the slope has flattened enough that water pools instead of running off. We rebuild or resurface the crown so it drains correctly and bonds tightly to the flue tiles. Crown repair in Daly City typically runs $400 to $1,000 depending on crown size and how much of the original needs rebuilding. We give you the price in writing first, and the estimate is free.
Cracks That Look Small Aren’t
A hairline crack in the crown opens up in a wet winter and lets water straight into the chimney structure. What shows as a small crack on top can mean stained masonry and a rusted damper far below. It’s one of the most common sources of chimney water damage.
Resurfacing vs. Rebuilding
If the crown is sound underneath, resurfacing restores the slope and finish at lower cost. If the concrete is crumbling through, a rebuild is the honest fix. We look at both and tell you which one applies.
Chimney Repair Companies
Chimney Repair Companies vary widely in what they actually do, and that difference matters when you’re choosing who works on your flue. Some outfits are general handymen who dabble in chimney work; some are sweep-only and hand off repairs to a subcontractor; a few cover inspection, sweeping, and repair themselves. We’re in that last group, with one company accountable for the whole job. We use professional-tier products from Copperfield, HeatShield, DuraFlex, and Gelco, matched to the repair, not to whatever’s cheapest. Repair costs in Daly City typically range from $150 for a minor fix up to $5,800 for a full reline, depending on scope. The written estimate sets the price.
Questions Worth Asking
Ask whether the company sweeps, inspects, and repairs in-house or coordinates between subcontractors. Ask what happens if a fix fails. Ask for the estimate in writing. A specialist can answer all three without dodging.

Why the Materials Matter
Generic substitutes show up in chimney work because most buyers can’t see inside a flue once the job is done. We’d rather you know the brand names we use and why we chose them. That’s why the fix we recommend has a name you can look up.
Chimney Masonry Repair
Chimney Masonry Repair is restoring the brickwork, mortar joints, and outer chimney structure when they’ve spalled, cracked, or come loose. Masonry needs repair when brick faces are flaking, mortar joints are receding, or the chimney leans or has visible gaps. We repoint joints, replace damaged brick, and rebuild sections where the structure has gone soft. Masonry repair in Daly City typically runs $600 to $2,500 depending on how much of the chimney is affected and how accessible it is. No work starts until you have the written estimate and have approved it.
Why Chimney Masonry Ages the Way It Does
Chimney masonry takes more direct weather than the rest of a house’s walls, which is why the chimney often fails first. Wet winters here work into joints that have already lost their tightness and speed the breakdown along. Catching it at the joint stage saves the brick.
The Case for Doing It Early
Repointing a few mortar joints is modest work. Rebuilding a soft chimney section because the joints went unattended is not. The cost gap between those two outcomes is where the real savings live.
Brands We Service
We work with Copperfield chimney products, which we know as a dependable line for masonry caps and topside components in this climate. We work with HeatShield liner restoration systems, which let us resurface qualifying flues instead of tearing them out. We work with DuraFlex flexible liner systems, matched to older and non-standard chimney configurations we see in Daly City homes. We also work with Gelco.
Whether you have Copperfield, HeatShield, DuraFlex, Gelco, or any other make, we can help. If the chimney uses products we don’t work with, we’ll tell you up front rather than force a fit. If you’ve had a repair done before and want a second opinion, we’ll look at it with the same evidence-first approach.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Water stains on the ceiling or firebox. Water marks usually mean flashing, crown, or cap trouble, and the source is rarely where the stain is. It’s worth finding out where the water actually enters before it does more damage.
- Loose or missing cap. A missing cap lets rain, birds, and debris into the flue, and it’s a quick fix compared to what it prevents. If you can see the flue opening from the ground, it needs a cap.
- Crumbling mortar joints. Receding or sandy mortar means the chimney masonry is letting water in. Repointing early is far less costly than rebuilding a soft chimney later.
- Cracked crown. If the concrete on top is cracked or flat, water will pool and seep into the chimney structure. A crown is a small repair now; water damage inside is not.
- Rust on the damper or a smoky smell. Rust or a smoky smell in the firebox often points to water intrusion or a failing flue. It’s a sign to have the whole chimney looked at, not just the firebox.
Our Process, Step by Step
- 1
Inspection first. We look at the flue, liner, crown, cap, flashing, and firebox before recommending anything. A camera inspection lets us see the full inside of the flue, and we photograph what we find.
- 2
We show you the evidence. Photos go in a report you keep, so you know what came through. We tell you what needs fixing now, what can wait, and what shouldn’t happen at all.
- 3
Quote in writing. You get a flat written estimate before we start, item by item, so nothing gets added without your say. No surprises when the job is done.
- 4
Repair with professional materials. Once you’ve approved it, we do the work using Copperfield, HeatShield, DuraFlex, or Gelco products matched to the repair. No substitutions at the end to save a dollar.
- 5
Final check. We confirm the fix does what it’s supposed to before we leave. If anything looks off afterward, we want to hear about it.
How Much Does Chimney Repair Cost in Daly City?
Our chimney repair cost in Daly City depends most on what’s actually wrong and how much of the chimney is affected. A typical flashing repair runs $350-$900, because roof access and pitch do a lot of the work. Crown repair runs $400-$1,000, and masonry repair runs $600-$2,500 depending on how much repointing or rebuilding is needed. Cap installation runs $180-$450, cap replacement $190-$475. A full liner installation is the big-ticket repair at $2,400-$5,800, but not every cracked flue needs one; qualifying chimneys can often be restored with HeatShield at lower cost. Minor fixes start around $150.
Repair price is driven by three things: which component failed, how high it is on the chimney, and whether the fix is restorative or a full replacement. What you should ask before accepting any estimate is how the price compares to doing nothing, because small fixes left alone tend to expand into structural work. Your free estimate includes the camera inspection and photo report, so the recommendation is backed by what’s actually in your flue, not a guess. You’ll see the photos before you see the price.
Our Service Area Near Daly City
We serve Daly City along with the neighborhoods around it, including Broadmoor and the border streets that run toward San Bruno and South San Francisco. We also work in Pacifica, Brisbane, and Millbrae, and south along the coast to Moss Beach and chimney repair in Montara. If you’re inland a bit, we reach West Menlo Park too. Response times vary by demand, but a repair estimate in Daly City is usually scheduled within a couple of days, and same-day openings come up. Call for the nearest available slot.
Serving Daly City, CA – Our Local Coverage Area
We serve Daly City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Daly City
Chimney repair is fixing any structural component of the chimney: crown, cap, flashing, masonry, or liner. It’s not a cleaning; the sweep removes soot and creosote, and the inspection finds what needs fixing. We keep all three under one roof so the person who finds the problem also fixes it. Call (866) 885-7416 for a look at your chimney.
Most small repairs take a few hours on the day of the appointment. A cap or flashing job typically finishes within a morning, and a crown rebuild or masonry repointing often needs the day. Liner installations run longer and may be scheduled across a day or two depending on flue length and access. You’ll get an accurate time window with your written estimate.
Repair costs in Daly City range from roughly $150 for a minor fix up to $5,800 for a full liner installation. Caps run $180-$475, flashing $350-$900, crown $400-$1,000, and masonry $600-$2,500 depending on scope. The written estimate sets the final price, and the estimate itself is free. Call (866) 885-7416 for an exact quote.
Yes, we work with DuraFlex liner systems and HeatShield restoration products, along with Copperfield and Gelco. Those are the product lines our repairs are matched to, and we use them where they’re the right fit for your chimney. If your chimney uses something else, we’ll tell you honestly whether it’s a job we handle.
Same-day repair is often possible when the fix doesn’t need custom parts and the schedule allows. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. Saturday we’re closed, so a call that day gets booked into the next opening. Liner jobs and masonry rebuilds are typically scheduled further out.
Our repair work is backed by the materials used and the way we install them, and we stand behind the fix if something’s not right. Specific terms depend on the product and repair type, so we go over them at the estimate stage. Ask us directly and we’ll tell you what applies to your job. Call (866) 885-7416.
Clear the fireplace area so we have room to work, and move anything fragile away from the hearth. If you use a gas insert, don’t light it the day we come out. Let us know about pets and parking when you book. That’s usually all we need. Call (866) 885-7416 to set the appointment.
Schedule Your Chimney Repair Service in Daly City Today
If something on your chimney looks off, the safest move is to have it looked at before the next burning season. One inspection covers your flue, liner, crown, and firebox, and we show you what we find before recommending anything. Call (866) 885-7416. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free, and nothing happens until you approve the written price. Scheduling a chimney inspection at the same time as your chimney sweep saves you a second appointment, and we also cover chimney repair in Moss Beach if you’re further down the coast.
Written by the team at Chimney Sweep Daly City.