Chimney Inspection in Daly City, CA | Chimney Sweep Daly City

Chimney Inspection in Daly City - One Flat Price, You See What We See

A flat-price sweep with a camera inspection and photo report included. If we find something that needs attention, you see the picture before you hear a price - and we will tell you when it can wait.

Flat price quoted before we book

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Inspection for Daly City Homeowners

A chimney inspection in Daly City is a safety and condition assessment of the whole venting system – flue, liner, crown, firebox, and the connections between them – and it’s how you find out what’s actually safe to burn in before the first rain sets in. The fog that rolls over the hills here keeps chimneys damp for long stretches, and damp masonry with a cracked flue is where trouble starts. Our technicians have up to 15 years of experience and show you what we find on camera before we recommend anything. We work with professional-grade materials from DuraFlex, HeatShield, Gelco, and Copperfield, and we handle inspection, sweep, and repair as one company so nobody points fingers later. Call (866) 885-7416 to book an inspection. We answer 24/7.

Professional chimney sweep cleaning and inspecting a residential fireplace in Daly City, CA

Call (866) 885-7416

Fireplace Inspection

Fireplace Inspection is the close look at the part of the system you actually use – the firebox, damper, smoke chamber, and the first stretch of flue above the fire – and it tells you whether a fire is safe to light. You need one before the first burn of the season, after any chimney fire, and whenever smoke comes back into the room or the damper stops working the way it used to. In Daly City’s older homes with original fireboxes, we often find mortar joints worn soft and damper plates that no longer seat. A fireplace inspection typically runs $150-$350 depending on whether we need camera work and how much of the firebox has to be opened up to see. We check the firebox lining, the damper, and the smoke shelf, then photograph what we see so you can look at it yourself.

Firebox and Damper Check

We examine the firebox brickwork and mortar for cracks that let heat reach framing, and we test the damper to make sure it opens and closes properly and seats when shut. A damper that won’t close is both a heat loss problem and a carbon monoxide route into the room. If we can repair a worn damper assembly rather than replace the whole unit, we’ll say so.

Smoke Chamber Condition

The smoke chamber is the sloped space between the firebox and the flue, and it’s where a lot of creosote collects in a fireplace that sees regular use. We inspect it for glazed buildup and for parging that has crumbled off the walls. Rough or damaged parging is a documented contributor to poor draft and to fires starting in the chamber itself.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Inspection Services

Chimney Inspection Services are the full assessment package we offer across Daly City: the outside of the stack, the flue, the crown, and the firebox, all checked together so you get one clear picture instead of four partial answers. You need this when you’ve bought a house, before you sell one, when an insurer asks for a condition report, or when it’s simply been a few seasons since anyone looked. Our technicians use a camera and a light to see the full length of the flue, take photos as they go, and give you a written report of what’s sound and what needs attention. A standard inspection typically runs $150-$300, and a fuller inspection with camera documentation runs $250-$500. Our technicians have up to 15 years of experience, and we work with HeatShield and Copperfield materials when repairs are warranted.

What We Look At Outside

From the roof we check the crown, the flashing where the chimney meets the roof, and the brick or siding for cracks and gaps that let water in. The crown in particular takes a beating here because it sits exposed to damp air for months at a time, and small hairline cracks grow into real leaks. We photograph each area so the report shows what we found.

What We Check Inside

Inside, we look at the firebox, damper, smoke chamber, and the full flue lining for gaps, cracks, and creosote buildup. The camera tells us what no flashlight from below can show – offset joints, separated liner sections, and the condition of the top of the flue. Anything that needs repair gets described in plain terms with the brand-specific fix we’d use.

Need help today?Fast, friendly service and a no-obligation free estimate.

Call (866) 885-7416

Chimney Flue Inspection

Chimney Flue Inspection is a focused look at the flue itself – the vertical passage that carries smoke and gases out of the house – because that’s the part that fails first and matters most. You need it whenever there’s been a chimney fire, whenever you smell smoke or creosote inside the house, or when the flue hasn’t been checked since the appliance was installed. We run a camera down the full length and check for cracked tile, broken joints, separated metal liner sections, and glazed creosote that has baked onto the walls. A flue inspection typically costs $175-$350 depending on access and whether a camera is needed. If the liner is worn but structurally sound, HeatShield ceramic resurfacing can restore it – a real alternative to pulling the whole liner and replacing it.

Flue Size and Draft

A flue that’s the wrong size for the appliance drafts poorly no matter how clean it is, and this is more common than homeowners expect in older Daly City homes that have had inserts added over the years. We measure the flue and compare it against the appliance, then tell you whether draft problems are a size issue or a blockage issue. That distinction decides whether a sweep fixes it or a liner replacement does.

Creosote Glazing

Creosote comes in stages, and glazed creosote is the hard, shiny, baked-on layer that won’t come off with a brush. It’s the fuel that makes chimney fires dangerous, and it builds faster in cool-burning, damp conditions than most people realize. We score it, explain what stage it’s at, and describe what it takes to remove it safely.

Chimney Fire

Chimney Fire is the emergency result we’re trying to prevent, and the inspection that follows one is the most important service we do. A chimney fire happens when creosote or soot in the flue ignites, and it can burn hot enough to crack tile, warp a metal liner, and open gaps that let heat reach framing. You need a thorough inspection after any fire – even one that sounded like a low roar or that put itself out – because the visible damage is rarely the whole story. Our post-fire inspection typically runs $250-$500 and includes a camera pass of the full flue and photos of every damaged section. We use DuraFlex liner systems to re-line flues that no longer hold up, and we’ll tell you plainly which sections are sound and which aren’t.

Recognizing the Signs

A roaring sound like a freight train, puffs of black smoke from the top of the chimney, a strong hot smell, or creosote flakes on the roof are all signs a fire has happened. Sometimes the only clue is a cracked flue tile found during a routine inspection after a fire the homeowner never noticed. Any of these signs justify booking an inspection before the next burn.

Post-Fire Assessment

After a fire, the flue has to be checked carefully for cracked tile, separated liner sections, and damage to the crown and the smoke chamber. We run the camera the full length, photograph each section, and compare what we see to the manufacturer’s requirements for the liner type. Then we tell you whether it can be restored, re-lined, or has to wait until conditions allow.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (866) 885-7416

Level 2 Chimney Inspection

Level 2 Chimney Inspection is the standard, camera-based assessment that goes beyond what you can see from the hearth, and it’s the one most Daly City homeowners actually need. It’s required when you buy or sell a home, after any chimney fire, whenever the appliance or fuel type changes, and after an earthquake or major storm. We inspect every accessible part of the system – the flue, the crown, the flashing, the firebox, and the connections – with a camera and take photos you keep. A Level 2 typically runs $250-$500 depending on roof access and how much documentation your insurer or buyer asks for. We work with DuraFlex and Olympia Chimney materials when a repair is called for, so you get a fix matched to what’s actually in your chimney.

When It’s Required

Real estate transactions, insurance condition reports, appliance changes, and post-fire checks are the usual triggers. If a lender, insurer, or buyer has asked for a Level 2, we can provide the written report and photos they need. If you’re not sure whether your situation calls for it, tell us what’s going on and we’ll tell you honestly whether a simpler check covers it.

Report and Photos

Every Level 2 comes with a written report describing the condition of each part of the system, plus photos from inside the flue. That record matters if you sell the home or file an insurance claim. We go through the report with you line by line so you know exactly what’s sound and what can wait.

Chimney Leak

Chimney Leak is water finding its way in – through the crown, the flashing, the brickwork, or the flue itself – and in Daly City’s damp climate it’s one of the most common problems we find on inspection. You need us when you spot staining on the ceiling near the chimney, water in the firebox, crumbling mortar, or a musty smell in the room after rain. Small leaks start as hairline cracks in the crown or a failed flashing seal and become structural damage over a few wet seasons. We trace the source rather than guessing, using the inspection camera and a close look at the roof-level details. Finding a leak typically costs $150-$400 as part of an inspection, and the repair itself is quoted separately once we know the source. We use Copperfield flashing components and proper crown repair materials, not caulk-and-hope patch jobs.

Finding the Source

Water shows up at the bottom of the chimney but almost always enters higher up, so we work top-down: crown first, then flashing, then brick and mortar, then the flue. That order matters because patching the wrong spot leaves the real leak running. The camera and photos make the source visible to you too.

Crown and Flashing Repair

A cracked crown lets water straight into the masonry, and failed flashing lets it slip in where the chimney meets the roof. Both are fixable when caught early, and both get worse with every wet season they’re left alone. We quote the repair separately from the inspection and tell you which fixes are urgent and which can wait.

Professional chimney sweep performing a detailed fireplace cleaning and inspection. in Daly City, CA
Want to talk it through?Free estimate, price agreed before work starts
Call (866) 885-7416

Chimney Camera Inspection

Chimney Camera Inspection is the part of the job that lets us see the inside of the flue without tearing anything apart, and it’s how we catch problems no flashlight can reach. You need it after any fire, before a liner decision, when there’s a persistent draft or smoke problem, and on any flue that’s more than a few years old. We run a high-resolution camera the full length of the flue and photograph every joint, offset, and section, then show you the images on the spot. A camera inspection typically runs $175-$350 depending on access and flue configuration. It’s the evidence behind every recommendation we make – nothing gets recommended without camera evidence you can see for yourself.

What the Camera Reveals

The camera shows tile cracks, separated metal liner sections, offset joints, and glazed creosote that a brush and flashlight can’t detect. It also shows the top of the flue and the condition of the liner termination. Each defect gets photographed so the report backs up what we tell you.

Seeing It Yourself

When we finish, we walk you through the images on a screen so you’re looking at the same thing we are. That’s the point – a homeowner shouldn’t have to take a stranger’s word for a four-figure repair. If the flue is sound and only needs a sweep, we tell you that too.

Brands We Service

We service DuraFlex flexible liner systems, which are common in retrofits and re-lining jobs on older or non-standard chimneys where a rigid liner won’t fit, and we know where those liners wear – at the top termination cap, at offsets, and at the appliance connection. We also work with HeatShield ceramic resurfacing, which is the system we use when a damaged flue can be restored from the inside instead of replaced, and we know which chimeras qualify and which don’t.

We service Gelco and Copperfield as well – Gelco components in the connections and terminations, Copperfield flashing and crown materials where the chimney meets the roof. The point of working with a defined set of professional product lines is that every fix is matched to a proven, warrantied material rather than improvised with a generic substitute. Whether you have DuraFlex, HeatShield, Gelco, Copperfield, or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need a price for your chimney cleaning?Free estimate, price agreed before work starts
Call (866) 885-7416

Signs You Need a Pro Right Now

  • Water stains on the ceiling or in the firebox. Water in the firebox after rain almost always comes from a crown or flashing problem higher up, and damp masonry gets worse every wet season. Left alone, a small leak becomes structural.
  • Smoke rolling back into the room. Backdraft means the flue isn’t drafting properly, which could be a blockage, a size mismatch, or a partially closed damper. Don’t keep burning – get it looked at.
  • A strong creosote smell when it rains. That musty creosote odor is a sign of buildup that has soaked into the masonry, and it usually gets worse in damp weather. It’s a sign a sweep is due.
  • Loose or missing mortar in the flue. Crumbling mortar inside the flue is a fire route into framing and a common finding on older Daly City chimneys. The camera is the only reliable way to see it.
  • You just moved in or can’t remember the last sweep. If you don’t know when the chimney was last checked, treat it as unchecked. Post-purchase inspection is the usual trigger.

Our Process, Step by Step

  1. 1
    Book and confirm. You call, we book you into the next available dispatch, and we confirm the appointment. We answer 24/7 and fast dispatch runs 7am to 7pm, Sunday through Friday.
  2. 2
    Exterior and roof-level check. We start outside – crown, flashing, brick and mortar – because that’s where most leaks begin. Photos back up everything we note.
  3. 3
    Interior inspection with camera. Inside, we check the firebox, damper, smoke chamber, and run the camera the full length of the flue. Every joint and section gets photographed.
  4. 4
    Report and recommendations. We walk you through the images, explain what’s sound, what needs repair, and what can safely wait. You see it before we recommend anything.
  5. 5
    Quote and repair if needed. If work is warranted, we quote it per job with a written estimate, using HeatShield, DuraFlex, Gelco, or Copperfield materials matched to your chimney. No work goes ahead without your approval.

How Much Does Chimney Inspection Cost in Daly City?

A typical chimney inspection in Daly City runs $150-$300 for a standard check, $250-$500 for a full Level 2 with camera documentation, and a flue-focused camera inspection runs $175-$350. Those ranges reflect how much of the system we have to open up and document, not a flat fee that adds up later.

What affects the price: whether roof access is needed, how much of the flue has to be camera-scanned, whether the flue configuration is standard or offset, and how much documentation your insurer or buyer has asked for. Older Daly City homes with retrofitted inserts or original fireboxes often take longer because the flue is a less familiar shape.

How to avoid overpaying: get the report in writing, ask to see the camera images, and don’t accept a recommendation for liner work without visible evidence. Our quotes are per job by written estimate – no hidden call-out fee, and nothing gets recommended without camera evidence you can see for yourself.

What’s included in a free estimate: we inspect first, then quote the repair separately. If nothing needs doing, we tell you that plainly and recommend a sweep only when it’s due. Our technicians have up to 15 years of experience, and we work with proven professional brands so the fix matches the chimney.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (866) 885-7416

Our Service Area Near Daly City

We serve Daly City and the surrounding towns – West Menlo Park, Broadmoor, San Bruno, Brisbane, South San Francisco, Pacifica, Millbrae, Montara, and Moss Beach. Response times depend on where you are and how the day’s bookings fall, but we book you in and confirm before we come. If you’re nearby and want the full picture of what we handle across Daly City, our team can explain the same three-phase approach – inspection, sweep, and repair – on every job.

Serving Daly City, CA – Our Local Coverage Area

We serve Daly City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Inspection in Daly City

Schedule Your Chimney Inspection Service in Daly City Today

Book a chimney inspection in Daly City and get a clear, camera-backed answer about what needs fixing and what can wait. Our technicians have up to 15 years of experience, we use professional-grade DuraFlex, HeatShield, Gelco, and Copperfield materials, and we show you what we find before we recommend anything. Call (866) 885-7416 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

Written by the team at Chimney Sweep Daly City.

Why Daly City Chooses Chimney Sweep Daly City

We set the standard for chimney inspection in Daly City.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Daly City

Getting your chimney inspection project started is simple.

1

Call or Request a Free Estimate

Tell us about your chimney inspection project and we set up a free visit. No obligation and no hidden fees.

2

Licensed Estimator Visits

A licensed, insured estimator inspects and measures on site, then gives you a clear written price.

3

Scheduled and Done Right

Your crew does the work on the date in your quote, backed by our workmanship warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney inspection pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Daly City Customers Say

Trusted by homeowners across Daly City and surrounding areas.

★★★★★

"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."

Shane Norris
★★★★★

"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."

Steven Chen
★★★★★

"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."

Allen Wong

Ready for Chimney Inspection in Daly City?

Call now for a free estimate, or request one below. Licensed, insured, and ready to schedule your free estimate in Daly City.

(866) 885-7416

Request a Free Estimate in Daly City

Tell us about your chimney inspection needs. We'll get back to you to set up your free estimate.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Local Service Coverage
Call Now - We Answer 24/7